GETTING FAMILIAR WITH PLUMBING: THE FIRST STEP FOR BATHTUB INSTALLATION

Getting Familiar with Plumbing: The First Step for Bathtub Installation

Getting Familiar with Plumbing: The First Step for Bathtub Installation

Blog Article

Request Service

We've unearthed the article pertaining to Tools You Need to Install a New Bathtub below on the web and felt it made perfect sense to discuss it with you on this site.


A Step-by-Step Guide to Installing a Bathtub
Setting up a bath tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably difficult job. If the old bathtub is easily accessible, the job can relocate rapidly; if you need to open up a wall to remove the old bathtub as well as place the brand-new tub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will certainly need an assistant to move out the old tub and embeded in the brand-new one. Make sure you have actually qualified on your own for the job and are comfortable attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Possibilities are you might require a professional plumber to make tube connections.
This post will certainly help you set up a new tub in your bathroom if you have currently bought a new bathtub and also do not require to transform the setup of your previous supply of water pipes.
Your tools and product list need to consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Removing Old Touches


    If you need to change old taps with new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain any type of water continuing to be in the system. The process of removing the existing faucets can be quite bothersome as a result of the restricted access that is frequently the situation.
    Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the remaining water that will come from the pipelines. Once the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
    Prior to going on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will need a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end supplies a connection to the existent supply pipelines.
    If you require to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next off, place the faucet in the placing opening in the bath/basin making certain that the washers are in area between the tap as well as the sink. Protect the tap in place with the maker supplied backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind needs to be attached to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.

    Mounting the Tub


    Making use of both wood boards under its feet, put the bath tub in the required position. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny factors.
    The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as changing the feet on the bathtub until the level reviews degree.
    To mount taps, fit all-time low of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the other tap.
    Turn on the supply of water and examine all joints as well as new pipework for leaks and also tighten them if essential. Load the tub and additionally examine the overflow outlet and the regular electrical outlet for leakages.
    Finally, fix the bathroom paneling as explained in the producer's user's manual. Tiling and securing around the bathtub needs to wait up until the bath tub has been made use of a minimum of when as this will certainly settle it right into its last setting.

    Planning for the Setup


    To start with, the sustaining frame supplied with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to avoid strain on the tub.
    Fit the flexible faucet connectors to the bottom of the two taps using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use all of the supplied washers.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its final setting.

    Tiling Around the Tub


    In the location where the bathroom meets the ceramic tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break a stiff seal, causing the water to pass through the wall in between the bathroom and also the tiling, resulting in difficulties with dampness as well as feasible leakages to the ceiling listed below.
    You can choose from a selection of coloured sealers to assimilate your fixtures and installations. They are offered in tubes and cartridges, as well as are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealer can fracture relatively early if you do not take into account this activity before sealing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the marketplace. It is advisable to fit the tiles making use of waterproof or water resistant sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    As an avid reader about How to Install a Bathtub, I thought sharing that article post was important. Appreciated our review? Please share it. Let others find it. We cherish reading our article about How to Install a Bathtub.


    Stop the flood! Call.

    Report this page